35 subjects: 34 documented views and one clearly labelled generic generator concept. Two unverified service features are listed outside the tour.
Exterior and door opening
Begin with the open rear doors and the performance arrangement. The model locates the side entrance; opening and preparation are manual.
Planned compact generator
An unbranded compact generator concept is shown in the modelled bay, using a 451 × 242 × 379 mm reference envelope. The view shows the proposed pull-out arrangement with the engine off. The generator actually installed in the trailer is unknown.
Side entrance
Locate the side entrance and see how its position connects the exterior with the interior layout.
Living space
The interior can serve different uses. Each arrangement is prepared separately; the alternative functions are not all available simultaneously.
Four-player DJ booth
See the four-player arrangement and the central mixer, with a clear view of the usable work surface.
Six-player DJ booth
Compare the six-player arrangement: four lower players and two elevated players around the central mixer. Equipment is positioned manually.
Inclining the console by hand
The recording shows the console being inclined by hand. The separate player/mixer detents requested for the model still need their own verified demonstration.
Kitchen, hob and sink
See the three-burner hob, sink and tap. Then watch the recording show the lower food cupboard left of the drawers opening, followed by the two drawers, the hinged cupboard below them and the two doors beneath the sink.
Kitchen and fridge arrangement
Compare the kitchen and fridge arrangement with the supplied source, including access and the surrounding units.
Washer and opening lid
The original clip shows access to the washer beneath the worktop and its top lid. The static 3D view locates the closed cabinet bay.
Shower and toilet
Compare the real bathroom recording with the model location: sliding door, shower fittings, tray, drain and toilet remain separate features. Model dimensions are visual fits, not measurements from this video.
Roof and rain shower
Inspect the roof and rain-shower feature in the corrected bathroom view.
Two retractable power sockets
In the original footage, the wall unit pulls out horizontally and the worktop unit rises vertically from its round cap. Compare their sockets and controls in the clip. The static 3D view locates the closed wall-unit cover.
Dining arrangement
The rear interior becomes a dining arrangement after manual preparation. Compare the table surface and seating with the DJ configuration.
Two laptop stations
See the two laptop workstations and how the working surfaces relate to the covered booth.
Bed raised
The bed is stored overhead to release the interior below. Inspect its raised position and clearance.
Wood-slat ceiling above the lowered bed
With the bed lowered, look up at the fixed ceiling, which is fully lined with wood slats. Distinguish it from the moving underside of the bed.
Bed lowered
Watch the interior seating area become a bed: the table folds and lowers, then the infill and cushions complete the surface. A wider view shows the upper bed and cupboards lowering separately. This excerpt preserves the timing of the supplied recording.
Centre cover
The centre cover is placed manually to change the usable surface above the booth.
Complete cover surface
Compare the complete set of three covers with the uncovered booth.
Handling the loose board
Watch the loose wooden board being lifted, turned and placed by hand. The complete three-cover storage route beneath the console still needs a verified demonstration.
Rear seat cushion
A manually placed rear cushion prepares the seating arrangement.
Rear sofa arrangement
The sofa cushions create a different rear seating arrangement. Compare their positions with the single seat.
Flat rear lounge
The flat lounge is another manually prepared arrangement of the rear area.
Outer bed inserts and level difference
Four small inserts and the leather pads join the outside resting area to the lowered inner bed; the leather bed end serves as a backrest. The owner specifies 1.6 m outside, 3.6 m combined length and a 20 cm level difference. These are supplied dimensions, not measurements from this recording.
Speakers removed and stored
The same two tall main cabinets stand upright on the interior rear floor below the booth. This is a two-cabinet arrangement, distinct from the setup with separate lower subwoofers.
Lower speakers deployed
The two tall main cabinets are placed by hand on the lower door platforms. They are the same cabinets later moved to the upper brackets.
Four door-mounted speakers
The static model view shows the prepared four-cabinet arrangement, with two upper main speakers and two lower subwoofers. Setup is performed by hand.
Speakers rotate inward and outward
The recording shows a mounted main cabinet being turned manually. The model camera shows the location; it does not reproduce the unverified bracket articulation.
Interior lighting
The original night image shows the blue ceiling lights. The 3D view locates the modelled fixtures; its lighting is a visualisation.
Rear view: event arrangement
Return to the rear to compare the five requested arrangements, beginning with the current event setup.
Rear view: photo arrangement with PA
Compare the separate four-cabinet model arrangement: two upper main speakers and two lower subwoofers. It is distinct from moving the same two main speakers between positions.
Rear view: outside bed and lounge
Compare the outside bed and lounge arrangement without speakers.
Rear view: laptop workstation
Inspect the laptop workstation from the rear with no speakers present.
Rear view: workstation with speakers
This model view combines two laptop stations with the upper main speakers. The lower subwoofers are outside this framing; the separate four-speaker view shows them. This composed arrangement illustrates the requested combination, which is not documented as a whole in the original footage.
